Відео

Is it still running ok?

YOUR THERMISTAT SHOULD BE ON THE OTHER PIPE

As far as I know UK shotguns must be permanently restricted to 2 in the magazine. Altering it to hold more shells will result in you needing to have it re proofed and put on a firearm certificate rather than a shotgun certificate. It would be easier to get a coterminous licence and to buy the FAC version. That said, I own that exact model of Mossberg and it is possible for the average gun owner to completely dismantle it for cleaning and maintenance.

Walking in front of a gun, using a phone for sound meter, calling it a moderator and taking 10 minutes to line up a shot at nothing just to hear what it sounds like….are you sure you know what you’re doing?

Hi I have the extract same one at home. However only difference is mine is mutifuel not oil. My question is what model is it? I have no data badge inside the cooker, so struggling to get spare parts.

Sounds basically the same lol

Hi, can you elaborate on how the unit is plumbed into the existing oil system? Im looking at doing the same. Thanks

Great job ! I like your shorter door with lower placement. The pivoting draft feature was a wise choice.

Nice vid. Must do this Liked and subscribed

Nice job

Is there a condensation drain valve at the bottom of this tank OR is it just going to eventually fill with water and rust out?

I believe it is a Reyburn supreme 216 MF

great video bud, it helped me to choose right thread reducer. thanks

only needed the 1 pipe sticking out from the T piece.. have a female fitting on the end so no air escape when no hose attached. other than that looks good.. i would of left the other handle on it plus then welded a couple of bars over the top to save anything getting damaged if it fell over or something fell on it...

Only 14k views this deserves more even after these years

very nice bike, did ypu make the red bull shock shrouds yourself mate?

Please turn the grinder around when using it.... man that's crazy

Way too much teflon tape..... 1 1/2 turns is all you need other wise it is useless

Thought I was going to see it rebuilt but a blank bit at the end ?

Simply done, well explained and illustrated where necessary, no unnecessary music except very faint Abba. Thank you very much. Love the mutts, by the way. A small point, if I were a tenth as skilled as you or so well able to instruct, I might smile occasionally. Thank you very much. Got a cylinder today and will get fittings tomorrow. Thanks again.

Does anyone know the exact names of all them fittings he used

Irimo España

My opinion and I don't know shit but I was thinking if you made the fill valve on the top and out to tool on bottom you could use a check valve on the fill line and you won't need to use a shut off

Jungle or desert US trouser in cotton RIP-stop will wear thin , the cotton poly or nylon blends tend to have more life in them depending on your climate or season. Also mfg may differ commercial vs USGI.

Great vido. Thanks for sharing.

£10,000

crude way of taping the threads,, just take a length off and keep it flat as you place it on,, your making it a thin sripe and not the full width the spool provides ,,, other wise nice efforts your sharing

And then after turning it over and both sides are dry it absolutely pisses down with rain...

Nice. Handy job

It looks cool.

Hi I’m looking for a damper door for solid fuel

0:43 ,2:54

Really nice, put some wheels on it and wheel it out to your car or wherever you need it. You've inspired me to build one. Do you do any spray painting or sand blasting? Would be interested to see how you'd go about building an "aftercooler" to cool down the compressed air before it goes into the tank to help prevent moisture travelling through to the gun.

thats a neat little stove :)

nice vid, when you apply teflon to pipe thread you always apply it clockwise on a right hand thread (same direction as when you tighten the nut

hey.. may i have the plumbing parts measurements?

Great video pal. Just a thought.. if you left the other handle on, maybe a cage could be built to protect all the plumbing?

if you're in the UK start with Builderdepot for these parts, example or their UNBELIEVABLE prices: 1/2'' Black Iron Equal Tee £0.41 1/2'' Black Iron Hex Nipple £0.32 1/2'' Black Iron Female to Female Socket £0.33 They are in the south mainly but do operate online too. Good luck guys!!!

Great job!👍

That horizontal section through the wall is to long a is not legal I believe

wow! i like it..very good tank colour and very good job! 👍👍👍👍👍

I have one from 1969. Beuitiful unfired condition. Predates Mossberg modern serial number system.

I think you can make it yourself, just loook and learn from woodprix .

ترجمة بالعربي

How much wood foes it use, do you get a lot of creosote buildup? I really want one of these for our old house

Nice repair/restore on that old workhorse. The snath (handle) is one of who knows how many European variations. The blade looks like it was made in Austria or Italy. Leaning towards Austria. Some many of the old manufacturers aren't around anymore so it hard to tell who's maker mark that is. The 70 is the blade length in centimeters.

That's a Mossberg 500 ,not a Remington.

Very well done , thanks . Not every one knows what a CALOR tanks is or how many KGS of gas it holds . 11.4 kgs i think

can a 200sfw be installed on a wooden floor

it would be good if you add a one way valve to the air inlet instead of ball valve.